![]() ft.' Be aware that this is very difficult for me to read as the font size is very. Pin.' This is then modified by footnote 3 which says '70-95 lbs. is permissible on nut when slot is in correct position for insertion of C. My wagon is a 1971, It was punched in the nose, It now has my old 70 El Camino front clip. My reproduction copy of the '68 Chevelle and El Camino Assembly Instructions says 'NUT-A torque of 125 lbs. You can find them on 67-72 GM A-bodies (Chevelle, Monte Carlo, El Camino, Skylark, GS, LeMans, GTO, Cutlass. There are several cars you can look for when searching for these spindles, and they are a direct swap onto any ’64-72 Chevelle. 68-72 CHEVELLE MONTE CONSOLE & AUTO SHIFTER. Stock Disc Spindles: GM was good at making things interchangeable, and the front spindles were no exception. 68-72 GTO CHEVELLE CUTLASS SKYLARK WIPER PARTS. In 1965 the El Camino got an upgrade with the higher performance version of the 27 engine rated at 350 horse power. 68-72 CHEVELLE GTO 442 GS LOCKOUT LINKAGE FOR AUTO TRANS. I've seen posts where it was shown that the 70-72 El Camino molding will work on the wagon tailgate (I believe it was shown using the lower for both the upper and the lower), but the 68-69 molding looks to be closer to the height of the molding originally on the wagon. The custom El Caminos had the Chevelle Malibu plush seats, a cloth-and-vinyl or all-vinyl bench, rich carpeting and the option of the highly styled Strato bucket seats and console, and an optional tachometer. My wagon is the VERY SELDOM SEEN COLOR IN 1970 ! ! OH GOD its RED ! 68-72 CHEVELLE GTO CUTLASS SKYLARK REAR END & SUSPENSION PARTS. Or in nine years or 37.000 miles no one has ever noticed it ! For the factory weld on rivits AKA studs to hold the trim clips, I used the little Phillips head screw in studs. The 67s were 60 inches, same as 65 and 66. Offset on the left side is about 1/4" of an inch. If the rear end you have measures 61 overall then it is a 68 or later. How much is my trim offset? From the edge of the trim to the edge of the door on the R. The thin or skinny factory trim has an embossed depressed area to clear the left side tailight area. When you mount the 1970 Camino trim on a wagon-68-72, OFFSET it to the right just a little ( no/one will notice it) WHY? When you open the gate like a door the 70 Camino trim will ALMOST hit on the left side. REPO stuff is a whole nother Friggen story. Wagon is painted, Go to mount REPRODUCTION -1970 El Camino tailgate trim. El Camino name, part number 3920867, replaced One of the most popular aspects of the 1971 Chevelle Super Sport was the rear end treatment. Mock up DONE all is perfect drill holes in T-Gate, Test mount Org. I believe I bought two SHORT pieces for a 70 to trim my tailgate on my Wgn. ![]() El Caminos have a long & a Short tailgate trim. I did my Nomad T, gate to match my 70 SS 454 El Camino. ![]() You will need 2 fenders (70 Elcamino),1970 Elcamino/wagon headlight extensions, hood (same as Chevelle), core support (same as Chevelle), fender tie bar (same as Chevelle), Front bumper and brackets (can use Chevelle or. It will all bolt on and the body lines and doors will match up. If you are speaking about trimming a Wagon tailgate, This may help. Yes you can do it with 1970 Elcamino sheetmetal.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |